Monday, March 27, 2017

Ivy Shakedown #7: Legion of Honor

Nice run up to the Legion of Honor.  Sunny, bit windy, though.  Clean ride.




Sunday, March 26, 2017

Run Ivy Run: Sunday Odd Jobs


  • No joy hooking up the engine guard.  It hits the exhaust and so doesn't line up with the bolt holes.
  • Switched the gas cap gasket to the new one, even though the old one looked just fine.  Will see if we get any more spills.
  • Stole the right hand bag from Roxy.  Bolted it up pretty much the same way but added an extra keeper bolt in the middle.
  • Added gas.
  • Lubed the chain.



Thursday, March 23, 2017

Run Ivy Run: Honk, Honk!

Wired up the horn.  Added a 3-way splitter to the power wire, but did a stand-alone ground wire for now.

Also used the new 30mm socket to torque the stem nut to 58 ft-lb, which was hard!  Really thought something was wrong because it seemed to take forever.



Sunday, March 19, 2017

Run Ivy Run: Horn and Torque


My plan was to actually run the horn off 4xAA batteries housed in the headlight bucket.  Had wired the entire thing up but when I hit the button, the horn briefly sounded then wouldn't come on again.  Checked all the wires, continuity and voltage and it was all fine.

Then tested against the SLA battery instead and found that it worked perfectly.

Would have maybe put more time into troubleshooting the 4xAA solution, but housing the battery box in the headlight seemed clunky.  Probably better off just doing up the loom with all the splits.

Got a few bags of connectors anyway, so I've got everything I need now.  To be continued...


Then set about torquing everything I could on the frame.  Went well with 3 exceptions:

  • The steering stem nut I'm using for Ivy is 30mm and the big socket I have is only 29mm.  Other stem nuts are 29mm so I must have only used it for those.  
  • The right side top fork bolt is spinning.
  • One of the rear flange bolts is spinning (marked it with red X)

Aside from that, here are the torque specs, which I also created a half-sheet file for:


  • Steering Head
    • Front axle nut (17mm) = 22
    • Handlebar lower bolts = 17-22 (didn't do these)
    • torque in this order
      •  Lower fork bolts (14mm) = 13-18
      • Top fork bolts (23mm) = 25-33 (only left was torqued)
      • Steering stem (29 or 30mm) = 58
  • Rear Suspension
    • Swing arm (17mm) = 22-25
    • Rear axle nut (17mm) = 22-29
    • Rear sleeve nut (23mm) = 29-36
    • Rear flange bolts (14mm) = 14-18
    • Rear cushions (14mm) = 18-25




Friday, March 17, 2017

Ivy Shakedown #6: Another Lesson Learned

As I was rolling the bike to door, I hear a scraping sound every time the wheel made a full rotation.  Upon closer inspection, realized the flange bolts were totally loose and hitting the back of the chain cover bolt!  They'd been heavily scored!

Another lesson learned.  Not only did I never lock down the keepers, the bolts were not even tightened down!

Tightened them up (but didn't torque).


On the plus side, had a perfect clean ride for Shakedown #6.


Thursday, March 16, 2017

Run Ivy Run: New Clutch & Shakedown #5

As expected, there was significant wear damage to the inside of the clutch cover.  The band of metal that holds the arm in place was very worn down.  Any further and it would have hit the arm itself.  Lesson Learned!

Went on to install the new (correct) pin-type clutch.  There was zero tension on the cable, which made it a breeze to install, but had a worrying moment when I thought there was too much slack to even engage the clutch at all.

Then realized that I could also use the extender in the middle of the cable (which had been hidden behind the tank).  With that adjusted, the take up and engagement was perfect.

Added 500mL at first.


Shakedown Rd #5

Good, clean laps.  Got her up to 3rd.  Shifting was smooth and deliberate. 

Came back to the box, found the oil level wasn't even registering, so added another 100mL.

Wednesday, March 15, 2017

Shakedown #4 & Demolished Clutch


Hectic testing session...


Started with a normal garage session.

First, checked the valve clearances.  They were closer to .07 than the .05 they should have been, but I was only checking to make sure they were not less than that.  Figured I would not adjust them yet.

Then tested idle using the battery from yesterday without charging it first.  She started and ran a solid idle for 10 straight minutes.

Would have swapped the carb but only now realized that the gas line is not only on the left, but angles DOWNWARD!  Would make for a very awkward fuel line.


Decided to just take it on a run.  Immediately got the slippage issue.  Did two laps that way and then boxed.


Changed and went back down for garage session #2.  Started off by draining the oil, then removed the exhaust and foot pegs to get the clutch cover off.

Found that the oil filter was almost clogged by a combination of gunk and also metal shavings!

Had intended to just swap that clutch for the one from the model engine, but ran out of time, so just brought them back up for inspection.  Good thing, too...


Took the clutch apart upstairs and it was DEMOLISHED!  The friction plates were fragments.  So mystery solved.

More concerning was that the clutch outer cover was very badly scored.  That could have explained the noise I'd been hearing at first (which disappeared once it was worn down.)  Also explains all the shavings.  That can't be good...  Hope the filter caught them all.

Took apart the pin-type clutch from the model engine to double check it.  Friction plates were 2.5mm and looked in good nick.  All the big springs were exactly 26mm as they were supposed to be.  Stole the little outer springs from the new eBay auto clutch.  Should be good to go.

Need to check what it was that scored the clutch outer cover and if it caused any damage internally.

Also, don't forget to add OIL!!